-- MIB Definition File ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
--
--  Copyright (c) 2022 Telect Inc, All Rights Reserved.
--
--  PURPOSE:      Defines the SNMP interface for the Telect Controller.
--
--  DESCRIPTION:  This file should be able to be compiled with any standard MIB compiler,
--                however our experience suggests that different compilers perform differently.
--
--  LAST UPDATED: 2022-03-20 00:00:00
-- MIB Module Name ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
TELECT-NRGCONTROL-MIB DEFINITIONS ::= BEGIN

-- Imported Items ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    IMPORTS
        enterprises, OBJECT-TYPE, 
                MODULE-IDENTITY, NOTIFICATION-TYPE,
                OBJECT-IDENTITY, Integer32, Unsigned32
            FROM SNMPv2-SMI
	OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE
	    FROM SNMPv2-CONF

         DisplayString, DateAndTime, TimeInterval
            FROM SNMPv2-TC

	 InetAddress, InetAddressType, InetAddressIPv4, InetAddressIPv6 
	    FROM INET-ADDRESS-MIB;

nrgControlMIB MODULE-IDENTITY
    LAST-UPDATED "2022030000Z"
    ORGANIZATION "Telect Inc."
    CONTACT-INFO "www.telect.com"
    DESCRIPTION "Telect nrgControl MIB"
	REVISION "202203020000Z"
	DESCRIPTION"Rev A7"
	    -Added IPV6 address definitions
	REVISION "202104140000Z"
	DESCRIPTION"Rev A6
		-modified ctrlDyCfgSnmpEnabled to have v1_enabled, v2_enabled, v3_enabled
		-modified ctrlDyCfgSnmpTrapEnabled to have v1_enabled, v2_enabled, v3_enabled"
    REVISION "202005150000Z"
    DESCRIPTION"Rev A5
    	-Added panel part numbers
    		spec48DCW8_12_2X100_A1NB(147907),
		    specCWG_8H1A413(147908),
		    nrg30ACS24V(147909),
		    nrg30ACS24V_E(147910),
		    nrg300CB08(147202),
		    nrg250TPA08(147203),
		    nrg240GT54(147204),
		    nrg125GMT10(147205),
		    nrg125GMT15(147206)"
    	
	REVISION "20209200000Z"
	DESCRIPTION"Rev A4
		-Added LAN DHCP Client Enabled config"
    REVISION "201505210000Z"
    DESCRIPTION"Rev A3
		-Changed atPnlSnsrType label from breaker(5) to feed(5)
		-Changed description for ctrlDyCfgSnmpEnabled to 'SNMP Traps Enabled'
		-Added dual600Amp10PositionBreaker(146326) to atPnlType
		-Added single600Amp20PositionBreaker(147103) to atPnlType"
    REVISION "201403210000Z"
    DESCRIPTION"Rev A2
		-Requires nrgOS 2.1 or later
		-Added atPnlSnsrErrorState
		-Added atPnlSnsrIsSmart
		-Added atPnlSnsrInstalledState
		-Added atPnlSnsrOnState
		-Added atPnlSnsrIsResettable
		-Added atPnlSnsrCriticalState
		-Added atPnlSnsrWarningState
		-Added atPnlSnsrTrippedState"
    REVISION "201402040000Z"
    DESCRIPTION"Rev A1
		-Requires nrgOS 2.0.3 or later
		-Changed atPnlSnsrAlarmState to BITS
		-Added atPnlSnsrCircuitID"
    REVISION "201210090000Z"
    DESCRIPTION"Rev A0
		-Initial Release"	
  ::= { telectPwrControllers 1 }


telect           	OBJECT IDENTIFIER ::= { enterprises 6842}
telectPower	    	OBJECT IDENTIFIER ::= { telect 2 }
telectPwrControllers  	OBJECT IDENTIFIER ::= { telectPower 1 }



-- OID Value Assignment and OBJECT-TYPE Construct ~~~~~~~~~~~~~~~~~~~~~~~~~~~~

----------------------------------------------
--          Controller                      --
--                                          --
--  This identifies the controller          --
----------------------------------------------
ctrlStaticConfig OBJECT-IDENTITY
   STATUS 	current
   DESCRIPTION "Controller information which is read-only over SNMP"
::= { nrgControlMIB 1 }

ctrlStCfgPN OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Controller Telect Part Number"
       ::= { ctrlStaticConfig 1 }

ctrlStCfgType OBJECT-TYPE
   SYNTAX  INTEGER
	   {nrgControl(142418),
	    nrgControlPlus(142419),
            bDFB(142420)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Controller Type"
       ::= { ctrlStaticConfig 2 }

ctrlStCfgMfgDate OBJECT-TYPE
   SYNTAX  DateAndTime
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Controller Manufacture Date"
       ::= { ctrlStaticConfig 3 }

ctrlStCfgSN OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..13))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Controller Serial Number"
       ::= { ctrlStaticConfig 4 }

ctrlStCfgLanFWRev OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..6))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "LAN Processor Firmware Revision"
       ::= { ctrlStaticConfig 5 }

ctrlStCfgWanFWRev OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..6))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "WAN Processor firmware Revision"
       ::= { ctrlStaticConfig 6 }

ctrlStCfgIPaddressFormat OBJECT-TYPE
   SYNTAX  InetAddressType
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "IP address format for all IP address values"
       ::= { ctrlStaticConfig 7 }

ctrlDynamicConfig OBJECT-IDENTITY
   STATUS             current
   DESCRIPTION "Controller information which is Read/Write over SNMP"
::= { nrgControlMIB 2 }

ctrlDyCfgName OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Controller Name"
       ::= { ctrlDynamicConfig 1 }

ctrlDyCfgBDFBConfig OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {notApplicable(0),
		       eightIndependentFeeds(1),
		       fourRedundantFeeds(2),
		       threeRedundantFeedsTopSkewed(3),
		       twoRedundantFeedsTopSkewed(4),
		       singleRedundantFeeds(5),
		       twoRedundantFeedsBottomSkewed(6),
		       twoRedundantFeedsEquallySkewed(7),
		       threeRedundantFeedsMiddleSkewed(8),
		       threeRedundantFeedsBottomSkewed(9)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "BDFB feed configuration - not applicable to standalone controllers "
       ::= { ctrlDynamicConfig 2 }

ctrlDyCfgMeasureInt OBJECT-TYPE
   SYNTAX  Unsigned32
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "How often measurements are recorded from sensors in seconds"
       ::= { ctrlDynamicConfig 3 }

ctrlDyCfgSiteID OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site ID"
       ::= { ctrlDynamicConfig 4 }

ctrlDyCfgSiteName OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site Name"
       ::= { ctrlDynamicConfig 5 }

ctrlDyCfgSiteAddr OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site Address"
       ::= { ctrlDynamicConfig 6 }

ctrlDyCfgSiteCity OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site City"
       ::= { ctrlDynamicConfig 7 }

ctrlDyCfgSiteState OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site State"
       ::= { ctrlDynamicConfig 8 }

ctrlDyCfgSiteZip OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site Zip"
       ::= { ctrlDynamicConfig 9 }

ctrlDyCfgSiteCountry OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Site Country"
       ::= { ctrlDynamicConfig 10 }

ctrlDyCfgTechName OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Technician name assigned to site"
       ::= { ctrlDynamicConfig 11 }

ctrlDyCfgNetworkID OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Network ID"
       ::= { ctrlDynamicConfig 12 }

ctrlDyCfgRegionID OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Region ID"
       ::= { ctrlDynamicConfig 13 }

ctrlDyCfgGPS OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "GPS coordinates should be xxx.xxxxxx,xxx.xxxxxx"
       ::= { ctrlDynamicConfig 14 }

ctrlDyCfgTz OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Timezone name"
       ::= { ctrlDynamicConfig 15 }

ctrlDyCfgTzDstEn OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
			   enabled(1)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Timezone DST Enable"
       ::= { ctrlDynamicConfig 16 }

ctrlDyCfgTzUtcOffset OBJECT-TYPE
   SYNTAX  Integer32
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "UTC timezone Offset in minutes"
       ::= { ctrlDynamicConfig 17 }

ctrlDyCfgTzDstOffset OBJECT-TYPE
   SYNTAX  Integer32
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "DST timezone Offset in minutes"
       ::= { ctrlDynamicConfig 18 }

	  
ctrlDyCfgLanIP OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN IP Address (IPv4)"
       ::= { ctrlDynamicConfig 19 }

ctrlDyCfgLanNM OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN Netmask (IPv4)"
       ::= { ctrlDynamicConfig 20 }

ctrlDyCfgLanGW OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN Gateway (IPv4)"
       ::= { ctrlDynamicConfig 21 }

ctrlDyCfgLanDNS OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DNS address (IPv4)"
       ::= { ctrlDynamicConfig 22 }

ctrlDyCfgWanDhcpEnabled OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
		       enabled(1)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "WAN DHCP Enabled "
       ::= { ctrlDynamicConfig 23 }

ctrlDyCfgWanIP OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "WAN IP Address (IPv4)"
       ::= { ctrlDynamicConfig 24 }

ctrlDyCfgWanNM OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "WAN Netmask (IPv4)"
       ::= { ctrlDynamicConfig 25 }

ctrlDyCfgWanGW OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "WAN Gateway (IPv4)"
       ::= { ctrlDynamicConfig 26 }

ctrlDyCfgWanDNS OBJECT-TYPE
   SYNTAX  InetAddressIPv4
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "WAN DNS address (IPv4)"
       ::= { ctrlDynamicConfig 27 }

ctrlDyCfgLanDhcpEnabled OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
		       enabled(1)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DHCP Server Enabled"
       ::= { ctrlDynamicConfig 28 }

ctrlDyCfgLanDhcpStartAddy OBJECT-TYPE
   SYNTAX  InetAddress
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DHCP Server Start Address"
       ::= { ctrlDynamicConfig 29 }

ctrlDyCfgLanDhcpEndAddy OBJECT-TYPE
   SYNTAX  InetAddress
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DHCP Server End Address"
       ::= { ctrlDynamicConfig 30 }

ctrlDyCfgLanLeaseTime OBJECT-TYPE
   SYNTAX  TimeInterval
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DHCP Server address Lease Time"
       ::= { ctrlDynamicConfig 31 }

ctrlDyCfgSnmpEnabled OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
		       v1_enabled(1),
			   v2c_enabled(2),
			   v3_enabled(3)}

   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "SNMP Traps Enabled"
       ::= { ctrlDynamicConfig 32 }

ctrlDyCfgSnmpTrapIP OBJECT-TYPE
   SYNTAX  InetAddress
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "SNMP Manager IPv4 Trap IP address"
       ::= { ctrlDynamicConfig 33 }

ctrlDyCfgDataServerEnabled OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
			   enabled(1)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Data Server Enabled"
       ::= { ctrlDynamicConfig 34 }

ctrlDyCfgDataServerUri OBJECT-TYPE
   SYNTAX         DisplayString(SIZE(0..40))
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Data Server URI"
       ::= { ctrlDynamicConfig 35 }

ctrlDyCfgDataServerPort OBJECT-TYPE
   SYNTAX  Unsigned32
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "Data Server Port Number"
       ::= { ctrlDynamicConfig 36 }

ctrlDyCfgLanDhcpClientEnabled OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {disabled(0),
		       enabled(1)}
   MAX-ACCESS         read-write
   STATUS             current
   DESCRIPTION "LAN DHCP Client Enabled "
       ::= { ctrlDynamicConfig 37 }

ctrlSnmpTrapAddress OBJECT-TYPE
    SYNTAX OCTET STRING (SIZE(0..40))
	STATUS current
	MAX-ACCESS read-write
	DESCRIPTION "Text for ipv4 or ipv6 SNMP trap address"
	::= {ctrlDynamicConfig 38}
	
ctrlAttachedPanels OBJECT-IDENTITY
   STATUS             current
   DESCRIPTION "All attached Panels"
::= { nrgControlMIB 3 }

ctrlAtPnlNbrPanels OBJECT-TYPE
   SYNTAX  Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Number of panels attached to this controller"
       ::= { ctrlAttachedPanels 1 }

ctrlAtPnlTable OBJECT-TYPE
   SYNTAX 	      SEQUENCE OF CtrlAtPnlTableEntry
   MAX-ACCESS 	      not-accessible
   STATUS	      current
   DESCRIPTION "Attached Panels Table"
       ::={ ctrlAttachedPanels 2 }

ctrlAtPnlTableEntry OBJECT-TYPE
   SYNTAX	      CtrlAtPnlTableEntry
   MAX-ACCESS 	      not-accessible 
   STATUS             current
   DESCRIPTION "An entry into Attached Panels Table"
   INDEX	      { atPnlIndex }
       ::= { ctrlAtPnlTable 1 }
	   
    

CtrlAtPnlTableEntry ::=
   SEQUENCE {
	atPnlIndex	Unsigned32,
	atPnlNumber	Unsigned32,
	atPnlName	DisplayString,
	atPnlPN		DisplayString,
	atPnlSN		DisplayString,
	atPnlType	INTEGER,
	atPnlMfgDate	DateAndTime,
	atPnlPosition	INTEGER,
	atPnlAuxSN	DisplayString,
	atPnlAuxMfgDate	DateAndTime,
	atPnlAuxPN	DisplayString,
	atPnlAuxFwRev	DisplayString,
	atPnlAuxFpgaRev	DisplayString,
	atPnlAuxType	INTEGER,
	atPnlNbrSensors Unsigned32
	}


atPnlIndex OBJECT-TYPE
   SYNTAX  Unsigned32
   MAX-ACCESS         not-accessible
   STATUS             current
   DESCRIPTION "Panel index for attached panels table"
       ::= { ctrlAtPnlTableEntry 1 }

atPnlNumber OBJECT-TYPE
   SYNTAX   	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "equal to the index so we can send in traps to identify panel"
       ::= { ctrlAtPnlTableEntry 2 }

atPnlName OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..40))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Panel Name"
       ::= { ctrlAtPnlTableEntry 3 }

atPnlPN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..18))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Panel Telect Part Number"
       ::= { ctrlAtPnlTableEntry 4 }

atPnlSN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..13))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Panel Serial Number"
       ::= { ctrlAtPnlTableEntry 5 }

atPnlType OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {dual100Amp10PosGMT(142409),
               bdfb800Amp20PosPod(142410),
               dual600Amp8PBrkr5PGMT(142411),
		       dual600Amp10PosBrkr(146326),
		       sgl600Amp20PosBrkr(147103),
		       nrg300CB08(147202),
		       nrg250TPA08(147203),
		       nrg240GT54(147204),
		       nrg125GMT10(147205),
		       nrg125GMT15(147206),
		       s48DCW8122X100A1NB(147907),
		       sCWG8H1A413(147908),
		       nrg30ACS24V(147909),
		       nrg30ACS24VE(147910)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Panel Type"
       ::= { ctrlAtPnlTableEntry 6 }

atPnlMfgDate OBJECT-TYPE
   SYNTAX  	      DateAndTime
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Panel Manufacturer Date"
       ::= { ctrlAtPnlTableEntry 7 }

atPnlPosition OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {undefined(0),
		       a1(1),
 		       b1(2),
		       a2(3),
 		       b2(4),
		       a3(5),
 		       b3(6),
		       a4(7),
 		       b4(8)}		
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "If this is a BDFB panel this value determines where the pod is located in the BDFB"
       ::= { ctrlAtPnlTableEntry 8 }

atPnlAuxSN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..13))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm Card Serial Number"
       ::= { ctrlAtPnlTableEntry 9 }

atPnlAuxMfgDate OBJECT-TYPE
   SYNTAX  	      DateAndTime
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm Card Manufacturer Date"
       ::= { ctrlAtPnlTableEntry 10 }

atPnlAuxPN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..18))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm Card Telect Part Number"
       ::= { ctrlAtPnlTableEntry 11 }

atPnlAuxFwRev OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..6))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm  Card Firmware Version"
       ::= { ctrlAtPnlTableEntry 12 }

atPnlAuxFpgaRev OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..6))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm Card FPGA Firmware Version"
       ::= { ctrlAtPnlTableEntry 13 }

atPnlAuxType OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {gmtPlusAlarmCard(142426),
		       gmtAlarmCard(142427),
		       loadCenterPlusAlarmCard(142428),
		       loadCenterAlarmCard(142429),
		       bdfbPlusAlarmCard(142430),
		       bdfbAlarmCard(142431),
			   nrgSmartAuxCard(142432),
			   integratedNoAux(147906)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Alarm Card Type"
       ::= { ctrlAtPnlTableEntry 14 }

atPnlNbrSensors OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Number of Sensors Attached to this panel"
       ::= { ctrlAtPnlTableEntry 15 }
	   
ctrlAtPnlSnsrTable OBJECT-TYPE
   SYNTAX 	      SEQUENCE OF CtrlAtPnlSnsrTableEntry 
   MAX-ACCESS	      not-accessible  
   STATUS	      current
   DESCRIPTION	"Attached Sensor Table"
::= { ctrlAttachedPanels 3 }

ctrlAtPnlSnsrTableEntry OBJECT-TYPE
   SYNTAX 	      CtrlAtPnlSnsrTableEntry 
   MAX-ACCESS	      not-accessible  
   STATUS	      current
   DESCRIPTION	"An Entry in the Attached Sensor Table"
   INDEX	      { atPnlIndex, atPnlSnsrIndex }
::= { ctrlAtPnlSnsrTable 1 }

CtrlAtPnlSnsrTableEntry ::=
   SEQUENCE {
	atPnlSnsrIndex				Unsigned32,
	atPnlSnsrNbr				Unsigned32,
	atPnlSnsrEquipSN			DisplayString,
	atPnlSnsrEquipName			DisplayString,
	atPnlSnsrInternalPN			DisplayString,
	atPnlSnsrEquipDate			DateAndTime,
	atPnlSnsrCircuitName		DisplayString,
	atPnlSnsrDecimalOffset		Unsigned32,
	atPnlSnsrLwrBound			INTEGER,
	atPnlSnsrLwrCritical		INTEGER,
	atPnlSnsrLwrWarn			INTEGER,
	atPnlSnsrUprWarn			INTEGER,
	atPnlSnsrUprCritical		INTEGER,
	atPnlSnsrUprBound			INTEGER,
	atPnlSnsrLwrWarnPcnt		Unsigned32,
	atPnlSnsrLwrCriticalPcnt	Unsigned32,
	atPnlSnsrUprWarnPcnt		Unsigned32,
	atPnlSnsrUprCriticalPcnt	Unsigned32,
	atPnlSnsrPrecision			INTEGER,
	atPnlSnsrType				INTEGER,
	atPnlSnsrPnlFeedNum			INTEGER,
	atPnlSnsrCircuitPos			Unsigned32,
	atPnlSnsrFormFactor			INTEGER,
	atPnlSnsrOption				INTEGER,
	atPnlSnsrCurrentRating		Unsigned32,
	atPnlSnsrControl			INTEGER,
	atPnlSnsrValue				Integer32,
	atPnlSnsrAlarmState			BITS,
	atPnlSnsrCircuitID			DisplayString,
	atPnlSnsrErrorState			INTEGER,
	atPnlSnsrIsSmart			INTEGER,
	atPnlSnsrInstalledState			INTEGER,
	atPnlSnsrOnState			INTEGER,
	atPnlSnsrIsResettable			INTEGER,
	atPnlSnsrCriticalState			INTEGER,
	atPnlSnsrWarningState			INTEGER,
	atPnlSnsrTrippedState			INTEGER
	}

atPnlSnsrIndex OBJECT-TYPE
   SYNTAX             Unsigned32
   MAX-ACCESS         not-accessible
   STATUS             current
   DESCRIPTION "Sensor index for an individual attached device 2nd index for sensor table"
       ::= { ctrlAtPnlSnsrTableEntry 1 }

atPnlSnsrNbr OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Sensor ID, same as sensor index"
       ::= { ctrlAtPnlSnsrTableEntry 2 }

atPnlSnsrEquipSN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..40))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Equipment Serial Number for item attached to this sensor"
       ::= { ctrlAtPnlSnsrTableEntry 3 }

atPnlSnsrEquipName OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..40))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Equipment Name for item attached to this sensor"
       ::= { ctrlAtPnlSnsrTableEntry 4 }

atPnlSnsrInternalPN OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..40))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Internal Part Number"
       ::= { ctrlAtPnlSnsrTableEntry 5 }

atPnlSnsrEquipDate OBJECT-TYPE
   SYNTAX  	      DateAndTime
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Date Equipment was commissioned on this sensor"
       ::= { ctrlAtPnlSnsrTableEntry 6 }

atPnlSnsrCircuitName OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..100))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Circuit Name"
       ::= { ctrlAtPnlSnsrTableEntry 7 }

atPnlSnsrDecimalOffset OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Decimal Offset for the sensor value - divide sensor value by this to get correct units"
       ::= { ctrlAtPnlSnsrTableEntry 8 }

atPnlSnsrLwrBound OBJECT-TYPE
   SYNTAX  	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Lower valid sensor range"
       ::= { ctrlAtPnlSnsrTableEntry 9 }

atPnlSnsrLwrCritical OBJECT-TYPE
   SYNTAX  	       Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Lower Critical Threshold for alarming"
       ::= { ctrlAtPnlSnsrTableEntry 10 }

atPnlSnsrLwrWarn OBJECT-TYPE
   SYNTAX  	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Lower Warning Threshold for alarming"
       ::= { ctrlAtPnlSnsrTableEntry 11 }

atPnlSnsrUprWarn OBJECT-TYPE
   SYNTAX   	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Upper Warning Threshold for alarming"
       ::= { ctrlAtPnlSnsrTableEntry 12 }

atPnlSnsrUprCritical OBJECT-TYPE
   SYNTAX  	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Upper Critical Threshold for alarming"
       ::= { ctrlAtPnlSnsrTableEntry 13 }

atPnlSnsrUprBound OBJECT-TYPE
   SYNTAX  	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Upper valid sensor range"
       ::= { ctrlAtPnlSnsrTableEntry 14 }

atPnlSnsrLwrWarnPcnt OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Lower Warning Percent - Valid for Current Sensors only"
       ::= { ctrlAtPnlSnsrTableEntry 15 }
	   
atPnlSnsrLwrCriticalPcnt OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Lower Critical Percent - Valid for Current Sensors only"
       ::= { ctrlAtPnlSnsrTableEntry 16 }
	   
atPnlSnsrUprWarnPcnt OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Upper Warning Percent - Valid for Current Sensors only"
       ::= { ctrlAtPnlSnsrTableEntry 17 }
	   
atPnlSnsrUprCriticalPcnt OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Upper Critical Percent - Valid for Current Sensors only"
       ::= { ctrlAtPnlSnsrTableEntry 18 }
	   
atPnlSnsrPrecision OBJECT-TYPE
	SYNTAX		INTEGER
			{ none(0),
			  one(1),
			  two(2)
			}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Sensor Precision"
       ::= { ctrlAtPnlSnsrTableEntry 19 }
	   
atPnlSnsrType OBJECT-TYPE
	SYNTAX		INTEGER
			{ noDevice(0),
			  current(1),
			  voltage(2),
			  temperature(3),
			  control(4),
			  feed(5)
			}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Sensor Type"
       ::= { ctrlAtPnlSnsrTableEntry 20 }

atPnlSnsrPnlFeedNum OBJECT-TYPE
	SYNTAX		INTEGER
			{ aFeed(0),
			  bFeed(1),
			  cFeed(2),
			  dFeed(3),
			  eFeed(4),
			  fFeed(5),
			  gFeed(6),
			  hFeed(7)
			}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Sensor Feed - typically A or B"
       ::= { ctrlAtPnlSnsrTableEntry 21 }

atPnlSnsrCircuitPos OBJECT-TYPE
   SYNTAX     	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Circuit Position - corresponds to the silkscreen on the front of the panel"
       ::= { ctrlAtPnlSnsrTableEntry 22 }

atPnlSnsrFormFactor OBJECT-TYPE
	SYNTAX		INTEGER
			{ notApplicable(0),
			  breakerOrTFD(1),
			  gmt(2),
			  inputFeed(3),
			  tpa(4),
			  sumFeed(5),
			  nrg250TPA08(15),
			  nrgSmartGMT(16)
			}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Current Sensor Form Factor"
       ::= { ctrlAtPnlSnsrTableEntry 23 }

atPnlSnsrOption OBJECT-TYPE
	SYNTAX		INTEGER
			{ notApplicable(0),
			  noSensorInstalled(1),
			  singlePole(2),
			  doublePole(3),
			  triplePole(4),
			  tfd(5),
			  multiPoleSlave(6),
			  singlePoleAlarmOnly(7),
			  doublePoleAlarmOnly(8),
		  	  triplePoleAlarmOnly(9)
			}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Options for sensor installed to allow for multipole configurations - valid for breakers only"
       ::= { ctrlAtPnlSnsrTableEntry 24 }

atPnlSnsrCurrentRating OBJECT-TYPE
   SYNTAX  	      Unsigned32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Current Rating of breaker/fuse installed"
       ::= { ctrlAtPnlSnsrTableEntry 25 }

atPnlSnsrControl OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {notPresent(0),
		       on(1),
		       off(2)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "If the circuit has remote control functionality - and what the state is if remote control is present"
       ::= { ctrlAtPnlSnsrTableEntry 26 }

atPnlSnsrValue OBJECT-TYPE
   SYNTAX  	      Integer32
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Sensor Value as integer - use Decimal offset to calculate correctly scaled value"
       ::= { ctrlAtPnlSnsrTableEntry 27 }

atPnlSnsrAlarmState OBJECT-TYPE
	SYNTAX		BITS {error(0), isSmartSensor(1), present(2), isOn(3), isResettable(4), criticalLevel(5), warningLevel(6), tripped(7)}
	MAX-ACCESS         read-only
	STATUS             current
	DESCRIPTION "Alarm State.  The values mean:
		error
			there is at least one error active such as multi-pole sensor missing or resettable sensor failure
		isSmartSensor
			the sensor has current monitoring capability
		present
			the sensor is installed at this location
		isOn
			the sensor will allow current to pass (if a current sensor type)
		isResettable
			the sensor at this position has the ability to be remotely reset
		criticalLevel
			the sensor is beyond the critical level
		warningLevel
			the sensor is beyond the warning level
		tripped
			the sensor detects a tripped breaker or blown fuse"

       ::= { ctrlAtPnlSnsrTableEntry 28 }

atPnlSnsrCircuitID OBJECT-TYPE
   SYNTAX             DisplayString(SIZE(0..100))
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Circuit Name"
       ::= { ctrlAtPnlSnsrTableEntry 29 }

atPnlSnsrErrorState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {normal(0),
		       error(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if there is at least one error active such as multi-pole sensor missing or resettable sensor failure"
       ::= { ctrlAtPnlSnsrTableEntry 30 }

atPnlSnsrIsSmart OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {nonMonitoring(0),
		       smartSensor(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor has current monitoring capability"
       ::= { ctrlAtPnlSnsrTableEntry 31 }

atPnlSnsrInstalledState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {empty(0),
		       present(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if a sensor is installed at this location"
       ::= { ctrlAtPnlSnsrTableEntry 32 }

atPnlSnsrOnState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {off(0),
		       on(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor will allow current to pass (if a current sensor type)"
       ::= { ctrlAtPnlSnsrTableEntry 33 }

atPnlSnsrIsResettable OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {notResettable(0),
		       resettable(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor at this position has the ability to be remotely reset"
       ::= { ctrlAtPnlSnsrTableEntry 34 }


atPnlSnsrCriticalState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {normal(0),
		       critical(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor is beyond the critical level"
       ::= { ctrlAtPnlSnsrTableEntry 35 }


atPnlSnsrWarningState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {normal(0),
		       warning(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor is beyond the warning level"
       ::= { ctrlAtPnlSnsrTableEntry 36 }

atPnlSnsrTrippedState OBJECT-TYPE
   SYNTAX  	      INTEGER
		      {normal(0),
		       tripped(1)}
   MAX-ACCESS         read-only
   STATUS             current
   DESCRIPTION "Shows if the sensor detects a tripped breaker or blown fuse"
       ::= { ctrlAtPnlSnsrTableEntry 37 }

ctrlProdEvents OBJECT-IDENTITY
	STATUS current
	DESCRIPTION "All controller trap definitions are under this node"
	::= { nrgControlMIB 10 }

ctrlEventDescriptors OBJECT-IDENTITY
	STATUS current
	DESCRIPTION "Event DESCRIPTION Node"
	::= { ctrlProdEvents 1 }

ctrlEventSeverity OBJECT-TYPE
	SYNTAX INTEGER {
			normal(1),
			warning(2),
			minor(3),
			major(4),
			critical(5)
			}
	MAX-ACCESS accessible-for-notify
	STATUS current
	DESCRIPTION "This value is sent with each trap as an indication of the severity of the event"
	::= { ctrlEventDescriptors 1 }

ctrlEventDescription OBJECT-TYPE
	SYNTAX DisplayString(SIZE(0..40))
	MAX-ACCESS accessible-for-notify
	STATUS current
	DESCRIPTION "Text which may provide further diagnostic info"
	::= { ctrlEventDescriptors 2 }

ctrlEventList OBJECT-IDENTITY
	STATUS current
	DESCRIPTION "NOTIFICATION objects are organized under this node"
	::= { ctrlProdEvents 0 }

snsrEvent NOTIFICATION-TYPE
	OBJECTS
	{
	  ctrlEventSeverity,
	  atPnlName,
 	  atPnlNumber, 
	  atPnlSnsrNbr,
	  atPnlSnsrType,
	  atPnlSnsrEquipName,
	  atPnlSnsrValue,
	  ctrlEventDescription
	}
	STATUS current
	DESCRIPTION "this trap is sent when a sensor passes a warning, critical boundary, or trips.  A normal will be sent out once the condition clears"
	::= { ctrlEventList 10 }

ctrlProdConformance OBJECT-IDENTITY
	STATUS current
	DESCRIPTION " Organization node for conformance objects"
	::= { nrgControlMIB 20 }

ctrlConfGroups OBJECT-IDENTITY
	STATUS current
	DESCRIPTION " Organization node for conformance groups"
	::= { ctrlProdConformance 1 }

ctrlProdConfigGroup OBJECT-GROUP
	OBJECTS
	{ 
   -- ctrlStaticConfig 
	ctrlStCfgPN,
	ctrlStCfgType,
	ctrlStCfgMfgDate,
	ctrlStCfgSN,
	ctrlStCfgLanFWRev,
	ctrlStCfgWanFWRev,
	ctrlStCfgIPaddressFormat,
   -- ctrlDynamicConfig
	ctrlDyCfgName,
	ctrlDyCfgBDFBConfig,
	ctrlDyCfgMeasureInt,
	ctrlDyCfgSiteID,
	ctrlDyCfgSiteName,
	ctrlDyCfgSiteAddr,
    ctrlDyCfgSiteCity,
    ctrlDyCfgSiteState,
    ctrlDyCfgSiteZip,
    ctrlDyCfgSiteCountry,
	ctrlDyCfgTechName,
	ctrlDyCfgNetworkID,
	ctrlDyCfgRegionID,
	ctrlDyCfgGPS,
    ctrlDyCfgTz,
    ctrlDyCfgTzDstEn,
    ctrlDyCfgTzUtcOffset,
    ctrlDyCfgTzDstOffset,
	ctrlDyCfgLanIP,
	ctrlDyCfgLanNM,
	ctrlDyCfgLanGW,
	ctrlDyCfgLanDNS,
	ctrlDyCfgWanDhcpEnabled,
	ctrlDyCfgWanIP,
	ctrlDyCfgWanNM,
	ctrlDyCfgWanGW,
	ctrlDyCfgWanDNS,
	ctrlDyCfgLanDhcpEnabled,
	ctrlDyCfgLanDhcpStartAddy,
	ctrlDyCfgLanDhcpEndAddy,
	ctrlDyCfgLanLeaseTime,
	ctrlDyCfgSnmpEnabled,
	ctrlDyCfgSnmpTrapIP,
	ctrlDyCfgDataServerEnabled,
	ctrlDyCfgDataServerUri,
	ctrlDyCfgDataServerPort,
    ctrlDyCfgLanDhcpClientEnabled	
	}
	STATUS current
	DESCRIPTION "Controller config conformance group"
	::= {ctrlConfGroups 1 }

ctrlAtDevGroup OBJECT-GROUP
	OBJECTS
	{ 
  -- ctrlAttachedPanels 
	ctrlAtPnlNbrPanels,
     -- ctrlAtPnlTable 
     	-- ctrlAtPnlTableEntry 
	atPnlNumber,
	atPnlName,
	atPnlPN,
	atPnlSN,
	atPnlType,
	atPnlMfgDate,
	atPnlPosition,
	atPnlAuxSN,
	atPnlAuxMfgDate,
	atPnlAuxPN,
	atPnlAuxFwRev,
	atPnlAuxFpgaRev,
	atPnlAuxType,
	atPnlNbrSensors,
     -- ctrlAtPnlSnsrTable
	-- ctrlAtPnlSnsrTableEntry 
	atPnlSnsrNbr,
	atPnlSnsrEquipSN,
	atPnlSnsrEquipName,
	atPnlSnsrInternalPN,
	atPnlSnsrEquipDate,
	atPnlSnsrCircuitName,
	atPnlSnsrDecimalOffset,
	atPnlSnsrLwrBound,
	atPnlSnsrLwrCritical,
	atPnlSnsrLwrWarn,
	atPnlSnsrUprWarn,
	atPnlSnsrUprCritical,
	atPnlSnsrUprBound,
	atPnlSnsrLwrWarnPcnt,
	atPnlSnsrLwrCriticalPcnt,
	atPnlSnsrUprWarnPcnt,
	atPnlSnsrUprCriticalPcnt,
	atPnlSnsrPrecision,
	atPnlSnsrType,
	atPnlSnsrPnlFeedNum,
	atPnlSnsrCircuitPos,
	atPnlSnsrFormFactor,
	atPnlSnsrOption,
	atPnlSnsrCurrentRating,
	atPnlSnsrControl,
	atPnlSnsrValue,
	atPnlSnsrAlarmState,
	atPnlSnsrCircuitID,
	atPnlSnsrErrorState,
	atPnlSnsrIsSmart,
	atPnlSnsrInstalledState,
	atPnlSnsrOnState,
	atPnlSnsrIsResettable,
	atPnlSnsrCriticalState,
	atPnlSnsrWarningState,
	atPnlSnsrTrippedState
	}
	STATUS current
	DESCRIPTION "Attached Device conformance group"
	::= {ctrlConfGroups 2 }	

ctrlEventGroup OBJECT-GROUP
	OBJECTS
	{ 
	-- ctrlProdEvents 
	-- ctrlEventDescriptors 
	ctrlEventSeverity,
	ctrlEventDescription
	}
	STATUS current
	DESCRIPTION "Event conformance group" 
	::= {ctrlConfGroups 3 }	

ctrlNotificationGroup NOTIFICATION-GROUP
	NOTIFICATIONS
	{ 
	-- ctrlEventList 
	snsrEvent
	}
	STATUS current
	DESCRIPTION "Notifications conformance group"
	::= {ctrlConfGroups 4 }

ctrlConformance MODULE-COMPLIANCE
	STATUS current
	DESCRIPTION "Sepecification of mandatory and non-mandatory MIB objects"
	MODULE -- this module
	MANDATORY-GROUPS{
		ctrlProdConfigGroup, 
		ctrlAtDevGroup, 
		ctrlEventGroup,
		ctrlNotificationGroup
	}
	::= { ctrlProdConformance 2 }

END